Fluke 500 Series Battery Analyzer — 3 mΩ to 3000 mΩ, for UPS and Substation Battery Testing
| Function | BT508 | BT510 | BT520 | BT521 |
|---|---|---|---|---|
| Resistance (mΩ) | Yes | Yes | Yes | Yes |
| Battery voltage | Yes | Yes | Yes | Yes |
| DC voltage | Yes | Yes | Yes | Yes |
| AC voltage and frequency (Hz) | — | Yes | Yes | Yes |
| Ripple voltage | — | Yes | Yes | Yes |
| Temperature at battery negative post | — | — | — | Yes |
| DC and AC current (and frequency) | — | — | — | Yes |
| DMM mode | Yes | Yes | Yes | Yes |
| Sequence mode | — | Yes | Yes | Yes |
| Discharge measurement mode | — | Yes | Yes | Yes |
| Auto measurement save | — | Yes | Yes | Yes |
| Wireless communication | — | — | — | Yes |
| Memory view | Yes | Yes | Yes | Yes |
Fluke specifies resistance accuracy as a percentage plus a digit count. The digit term converts to a fixed offset in milliohms and dominates at the bottom of each range, so the headline percentage is never actually achieved at low readings.
| Range | Resolution | Accuracy spec | Digit term = | At 1/6 of range | At mid range |
|---|---|---|---|---|---|
| 3 mΩ | 0.001 mΩ | ±(1 % + 8) | 0.008 mΩ | ±0.013 mΩ at 0.5 mΩ → 2.6 % | ±0.034 mΩ at 2.64 mΩ → 1.3 % |
| 30 mΩ | 0.01 mΩ | ±(0.8 % + 6) | 0.06 mΩ | ±0.10 mΩ at 5 mΩ → 2.0 % | ±0.14 mΩ at 10 mΩ → 1.4 % |
| 300 mΩ | 0.1 mΩ | ±(0.8 % + 6) | 0.6 mΩ | ±0.9 mΩ at 50 mΩ → 1.8 % | ±1.4 mΩ at 100 mΩ → 1.4 % |
| 3000 mΩ | 1 mΩ | ±(0.8 % + 6) | 6 mΩ | ±14 mΩ at 1000 mΩ → 1.4 % | ±26 mΩ at 2500 mΩ → 1.0 % |
| Function | Range | Resolution | Accuracy | Models |
|---|---|---|---|---|
| Battery resistance / strap resistance (battery voltage ≤60 V) | 3 mΩ | 0.001 mΩ | 1 % + 8 | All |
| Battery resistance / strap resistance (battery voltage ≤60 V) | 30 mΩ | 0.01 mΩ | 0.8 % + 6 | All |
| Battery resistance / strap resistance (battery voltage ≤60 V) | 300 mΩ | 0.1 mΩ | 0.8 % + 6 | All |
| Battery resistance / strap resistance (battery voltage ≤60 V) | 3000 mΩ | 1 mΩ | 0.8 % + 6 | All |
| V dc | 6 V / 60 V / 600 V | 0.001 / 0.01 / 0.1 V | 0.09 % + 5 | All |
| V dc | 1000 V | 1 V | 0.09 % + 5 | BT521 |
| V ac (45–500 Hz, with 800 Hz filter) | 600 V | 0.1 V | 2 % + 10 | BT510, BT520, BT521 |
| Frequency (displayed with V ac and A ac) | 500 Hz | 0.1 Hz | 0.5 % + 8 | BT510, BT520, BT521 |
| AC voltage ripple (20 kHz max) | 600 mV | 0.1 mV | 3 % + 20 | BT510, BT520, BT521 |
| AC voltage ripple (20 kHz max) | 6000 mV | 1 mV | 3 % + 10 | BT510, BT520, BT521 |
| A dc / A ac (with optional Fluke i410 clamp) | 400 A | 1 A | 3.5 % + 2 | BT521 |
| Temperature | 0 to 60 °C | 1 °C | 2 °C (4 °F) | BT521 |
Not directly. It measures internal resistance, voltage, ripple and frequency, and those are indicators — a rising resistance correlates with lost capacity, but the instrument does not perform a discharge test and does not output an Ah figure. The Discharge VOLTS mode on BT510 and above records cell voltage at intervals during a load test you perform separately, and from that you can calculate the time to cut-off and so the capacity loss. If a customer's acceptance criterion is a measured capacity, they need a load bank and this instrument is the wrong purchase.
Four questions decide it. Do you need readings saved automatically while testing a string? If yes, BT508 is out — it has no sequence mode and no auto-save. Do you need ripple and AC voltage? If yes, BT508 is out. Do you need the probe with its own display and verbal battery-ID count? That is BT520 and up. Do you need temperature at the post, or DC/AC current with the i410 clamp? That is BT521 only, and there is no retrofit. Most maintenance teams that walk strings land on BT520; teams that also document temperature land on BT521.
No. The resistance function is specified for battery voltage of 60 V or less, so on a 110 V or 220 V bank you measure cell by cell or block by block. The instrument's own input rating is CAT III 600 V with 1000 V dc maximum, which is a safety rating for working around the equipment — it is not a statement that resistance can be measured across the whole string. Treating the two numbers as interchangeable is a common and expensive misreading.
It uses the AC injection method: a signal of under 100 mA at 1 kHz is injected and the impedance determined from the response, using four-terminal Kelvin connections. Because the excitation is small, there is no heating and no meaningful disturbance, so batteries can be tested in place on float. You do need access to the terminal posts, and the reading is taken at the posts — the 4-wire connection is what removes lead and contact resistance from the measurement.
Both, depending on how you present it. The instrument reports resistance in milliohms; the Fluke Battery Management software can switch stored results between conductance and resistance readings (software version 1.0.69 or later). This matters when a customer wants to compare against an older conductance-based baseline — the conversion is handled in software, so do not attempt to convert by hand.
BTL10 is the basic Kelvin test lead set with a save button at the tip, supplied with every model. BTL20 is the intelligent probe set: its own LCD, visual warning indication, voice count for the battery ID, integrated save button, and long and short extenders for double-stacked trays — supplied with the BT520. BTL21 adds an integrated infrared temperature sensor to the same package and is supplied with the BT521. They are not interchangeable across models for the intelligent features: fitting a BTL21 to a BT510 does not add temperature measurement to the instrument.